GTU Study
KHUDKIBOOK
INTRODUCTION TO STRENGTH
FREE PDF
3340101
Code: 3340101
Credits: 6
Semester 4
CIVIL
Introduction To Strength Of Materials
Get the full GTU study material, English & Gujarati textbook PDFs, syllabus curriculum, and solved previous year question papers.
×
English Book & Chapters
English Book Coming Soon
We are working hard to add this material. Stay tuned for updates!
Follow on Instagram for Updates
×
GTU Previous Year Papers
Introduction To Strength Of Materials Syllabus — Unit-wise Content
The official GTU curriculum for Introduction To Strength Of Materials (subject code 3340101) as prescribed for CIVIL · Semester 4 divides the course into 8 units, covering 43 listed topics. The unit-wise breakdown below is read from the GTU syllabus document for this subject code, so you can check what the course actually covers before deciding which papers to attempt.
Download the official syllabus PDF (3340101)Unit 1 INTRODUCTION TO DIRECT STRESS & STRAIN
- 1.1. Different types of Structures and Loads
- 1.2. Direct Stress , linear Strain , Hook’s Law Calculate Numerical on Direct Stress & Linear Strain , Stress Strain curve of Mild Steel , Modulus of Elasticity ,Yield , Breaking & Ultimate Stress and factor of Safety.
- 1.3. Lateral Strain and Poission’s ratio. FUNDAMENTALS OF FLUID MECHANICS Course Code: 3340101
- 1.4. Temperature Stresses & Strain with & without yielding.
- 1.5. Shear Stress , Shear Strain & Shear Modulus.
- 1.6. Bulk Modulus & Volumetric Strain.
- 1.7. Differentiate Sudden , Gradual & Impact Load Strain Energy & Proof Resilience for Sudden ,Gradual & Impact Load with Numerical Problems.
Unit 2 MOMENT OF INERTIA
- 2. Compute Moment of Inertia of Symmetric & asymmetric structural sections
- 2.1. Moment of Inertia & its Importance.
- 2.2. Parallel & Perpendicular Axis Theorem.
- 2.3. Formula of Moment of Inertia of solid & Hollow sections like Rectangle , Triangle , Circle.
- 2.4. Moment of Inertia about C.G for I section , H section , Channel Section , Angle Section , T Section and Built up Section having flange plates to I & H Section and of Double Channels back to back & toe to toe.
Unit 3 S.F & B.M IN BEAM
- 3. Draw Shear Force & Bending Moment Diagram for Statically Determinate Beams.
- 3.1. Statically Determinate Beams Like Cantilever , Simply Supported & Over Hang Beam
- 3.2. Relation between Shear Force and Bending Moment
- 3.3. Sagging & Hogging Bending Moment and its importance
- 3.4. Point of Contra flexure & its importance
- 3.5. S.F & B.M Diagram for Cantilever , Simply Supported & Over Hang Beam elements like shaft , axle , spindle subjected to Point Load and/ or U.D.L.
Unit 4 BENDING STRESSES IN BEAM
- 4. Use ‘ Theory of Bending’ to compute stresses in Beams.
- 4.1. Bending Theory Equation Bending stress , Sectional Modulus , Neutral Axis Application of Bending theory to Statically determinate beams elements like shaft , axle, spindle , pulley arm having rectangular or circular section to find out stresses.
Unit 5 DEFLECTION OF BEAMS
- 5. Determine deflection induced in Statically Determinate Beams.
- 5.1. Slope & Deflection
- 5.2. Formulae for Cantilever Beam subjected to Point Load at free end and with full UDL.
- 5.3. Formulae for S.S Beam subjected to Point Load at MID SPAN and with full UDL
- 5.4. Numerical problems on Slope and Deflection for 5.2 & 5.3
Unit 6 COLUMNS & STRUTS
- 6. Calculate Load carrying capacity of Column & Strut.
- 6.1. Column & Strut.
- 6.2. Short & Long Column.
- 6.3. End Condition of Column and effective Length of Column & Modes of Failure in Column.
- 6.4. Radius of Gyration , Slenderness Ratio.
- 6.5. Euler’s Crippling Load & its numerical
- 6.6. Rankin’s load / Buckling Load of Column / FUNDAMENTALS OF FLUID MECHANICS Course Code: 3340101 screw of screw jack & its numerical.
Unit 7 COMBINED DIRECT & BENDING STRESSES
- 7. Analyse Structural components subjected to Axial Eccentric Loads
- 7.2. Formula for combined Direct &Bending Stresses
- 7.3. Limit of Eccentricity.
- 7.4. Core section for Rectangular & Circular ( Hollow & Solid )
- 7.5. Numerical on Combined Stresses for Rectangle & Circular Section
Unit 8 TORSION
- 8.1. Analyse Machine Components subjected to Torsion for torsional stress
- 8.2. Calculate Power Transmitted by Shaft , spindle and axle subjected to Torsion.
- 8.1. Torsion , Angle of Twist , Polar Moment of Inertia , Torsional Rigidity.
- 8.2. Formula of Torsional Stress.
- 8.3. Formula for Power Transmitted Consumed for shaft , spindle and axle of solid and hollow sections subjected to Torsion.
- 8.4. Numericals based on 8.2 & 8.3.
Study on Android App:
